Reverse Osmosis Storage Tank: Empty Air Charge

By SubcontractorHub Editorial Team·Published November 2026

Dealer notes beside a reverse osmosis storage tank before the empty air charge is checked

Quick Answer

A reverse osmosis storage tank, in four Pentair manuals fetched for this page, is set to 5 to 7 psi when the tank is empty. The gallon marks are not the same: 2.8, 3.2, 2.1, and a 1.9 to 3.2 range, each on its own model. Read the tank you have. This is not a drawdown percent.

Low flow at the faucet is often blamed on the membrane. The manuals fetched here put a different check first when the complaint is pressure or volume in the tank: empty it, then read the air side. Filter clocks and the membrane test stay on other pages. This one is the reverse osmosis storage tank itself.

What a Reverse Osmosis Storage Tank Is For

The RO2050 manual says the system does not produce a high volume of water on demand the way an ordinary filter does. Water is produced slowly. The system needs about 2 to 4 hours to fill the storage tank. As water is taken, production starts again and stops when the tank is full. The tank is the buffer. It is not the membrane, and it is not the prefilter.

The same manual says that for each gallon produced, several gallons are discharged as reject water. It does not print a ratio such as three to one. This page will not add one. The maintenance intervals for that system, including the 2.8 gallon capacity already named there, stay on reverse osmosis maintenance. The membrane test stays on the reverse osmosis membrane page.

The Empty-Tank Number Four Manuals Share

The RO2050 specifications line says tank air pressure, empty, is 5 to 7 psi. The troubleshooting block for no pressure at the faucet or low volume in the tank says to close the cold supply, empty the tank, and check with a pressure gauge when the tank is empty. An empty tank should contain 5 to 7 psi. Add or release air to land in that band. Then open the supply and let the system run for 3 hours before you judge it again.

The GRO-475B manual prints the same empty-tank band, 5 to 7 psi, and the same empty-then-gauge order, including the note that a bicycle pump may be needed to get the last water out. The GRO-350BP manual prints tank air pressure empty as 5 to 7 psi on its specifications. The Everpure residential install note says the tank's air pressure is factory set at 5 to 7 psi when the tank is empty.

Four manuals, one band, and a shared condition: empty. A gauge on a tank that still has water in it is not the reading those sentences describe. This page does not convert 5 to 7 psi into a usable-gallon percent. That percent was not in these files.

Gallon Marks Are Model Marks

Capacity is where the four files split. Treat each line as that model, not as "a reverse osmosis tank."

ManualCapacity printedAir chargeOther line on that page
RO20502.8 gal maximum5 to 7 psi emptyAbout 2 to 4 hours to fill
GRO-475B3.2 gal maximum5 to 7 psi emptyFull weight listed at 25.50 lb
GRO-350BP2.1 gal maximum5 to 7 psi emptyFull weight listed at 19.50 lb
Everpure residential1.9 to 3.2 galFactory set at 5 to 7 psi emptySupport the tank; full weight called out as about 40 lb on that install note

The Everpure note also says that when the tank is full it weighs approximately 40 pounds, and it tells the installer to support it. GRO-475B lists a full weight of 25.50 pounds. GRO-350BP lists 19.50 pounds. Those are different tanks. Do not average them into one "typical" tank and put that average on a quote.

How the Manuals Say to Check a Reverse Osmosis Storage Tank

The RO2050 and GRO-475B blocks are the same sequence. They are quoted here as those manuals' troubleshooting, not as a procedure invented for every brand under the sink.

  1. Close the cold water supply to the system.
  2. Lift the tank. If it is not empty, open the drinking-water faucet and run it until it is.
  3. If water remains, the note says a bicycle pump may be needed to push the rest out. Stop if the plan was only a glance at the gauge.
  4. With the tank empty, read the air pressure. The line says an empty tank should contain 5 to 7 psi.
  5. Add or release air until the reading is in that band. The manuals say to increase or decrease accordingly. They do not name a target of 7.5 or 8.
  6. Open the cold supply. The RO2050 and GRO-475B steps say to let the system run for 3 hours, then check performance. If it has not improved, they say to call technical support.

If water comes out of the air valve instead of air, these fetched pages do not give the next price. They do not say "replace the tank" in the sentences used here. Write down what came out of the valve and follow the manual for that model. A price for a new tank was not fetched.

What This Page Will Not Borrow From a Well Tank

A well pressure tank is pre-charged a couple of psi below the pump's cut-in. That rule lives on the well-pump sizing tool and is a different vessel. A reverse osmosis storage tank in these manuals is a small bladder tank at 5 to 7 psi empty, downstream of a membrane, not a 30/50 switch. Do not copy the well-tank offset onto the drinking-water tank.

The reverse osmosis system cost calculator is a different page. Dollar bands on it were not re-fetched for this article, so they are not repeated. If the visit is a filter change rather than an air check, use the maintenance page. If the complaint is a rising TDS number, use the membrane page. The air charge does not answer either of those.

What to Write on the Service Record

A dealer who only writes "RO tank checked" has not written the reading. The record that matches these manuals has four lines: the model, whether the tank was empty when the gauge went on, the psi that was there, and the psi after the adjustment if one was made. Add the wait you actually used before the second flow check. The RO2050 says about 3 hours in that troubleshooting step, and about 2 to 4 hours to fill from the startup note. Those are that manual's clocks. They are not a promise that every kitchen is full in three hours.

Keep the raw psi next to the customer, the way a pH reading stays next to a neutralizer. The next technician should not have to guess whether the last visit charged a full tank or an empty one. Plans for keeping that note on the job are on /plan. This page does not claim a callback rate for writing the number down.

What a Public Search Showed

A public search on 18 November 2026 for tank pressure turned up calculator blogs that print 7 to 8 psi and a usable-water percent. Those blogs were not used. The numbers above are the four Pentair manuals. No Ahrefs volume was refreshed for this head term. Demand is that public result list, and the gap is the air charge the maintenance article did not print.

Frequently Asked Questions

What air pressure does a reverse osmosis storage tank need when it is empty?

Four Pentair manuals fetched on 18 November 2026 print 5 to 7 psi with the tank empty. That is the RO2050, the FreshPoint GRO-475B, the FreshPoint GRO-350BP, and an Everpure residential manual. The number is for those tanks, read empty. It is not a guess for every brand.

Why does the reverse osmosis storage tank have to be empty for the reading?

The RO2050 and GRO-475B troubleshooting steps say to empty the tank, then check pressure, and that an empty tank should contain 5 to 7 psi. Water still in the tank presses on the bladder, so the gauge is not reading the air charge those steps describe. A note on both manuals says a bicycle pump may be needed to push the last water out.

How much water do those manuals say the tank holds?

The fetched pages do not agree with each other, because they are different models. RO2050 lists a maximum of 2.8 gallons. GRO-475B lists 3.2 gallons. GRO-350BP lists 2.1 gallons. The Everpure note lists 1.9 to 3.2 gallons. Use the plate on the tank you are standing next to.

Does a reverse osmosis storage tank replace the filter schedule?

No. Filter and membrane intervals stay on the reverse osmosis maintenance page. This page is the air charge and the labeled capacity. A tank that is charged correctly can still be downstream of a clogged prefilter.

SubcontractorHub

See How Top Contractors Close More Jobs

AI proposals, sales pipeline, and project management — all in one platform.

  • ✓AI-powered proposals in the field
  • ✓CRM built for contractor sales
  • ✓Project tracking from sale to install
Book a Free Demo →

30 minutes. No commitment.