Free Calculator · By SubcontractorHub Editorial Team · Published November 2026

Drip Edge Calculator for Sticks, Not Fascia Boards

A drip edge calculator on this page adds the eave to the rake. Eighty feet plus 40 feet is 120 linear feet. Sticks stay blank until you type a stock length.

Built by SubcontractorHub — the software contractors use to quote, finance, and run every job.

Book a Demo

How the Drip Edge Calculator Uses the Lengths You Measured

Eave plus rake. A stick count only after you type the piece.

Eighty and forty are lengths in the boxes. They are not a house. Sticks stay blank until you type a stock length.

This drip edge calculator reads 120.0 linear feet. No sticks, because no stock length was typed.

All calculations are estimates based on historical information and should be verified by the user.

Important: the rake is already the sloped length

All calculations are estimates based on historical information and should be verified by the user. This tool is provided as a free service for planning purposes only and is not a substitute for a professional assessment, a supplier quote, or applicable local code requirements.

This Drip Edge Calculator Does Not Stretch a Rake

Fascia that starts from a flat rake and a rise per 12 is the fascia board calculator. That page's job is the board. This page's job is the metal, and only after you have already measured the rake along the slope. Typing a level run here would be short. Do that pitch step before you open this box, or on the fascia page, not both.

Rafter length is the rafter calculator. Soffit area under the eave is the soffit calculator. Squares of shingles are a different takeoff. None of those three is a stick of edge metal.

Worked edge

Eave 80 feet. Rake 40 feet. The length is 120 linear feet. Stick blank. Lap blank, which means the stick is not shortened, and there is still no stick count. A hand check: a 10 foot stick with a 2 inch lap covers 9.833 feet, and 120 divided by 9.833 rounds up to 13 sticks. Ten and two are numbers you would type. They are not in the boxes.

LineInputExample
Eavefeet, level80
Rakefeet, already along the slope40
Lengtheave + rake120 ft
Stickfeet, typedblank
Sticksceil(length / usable)blank

How should you measure before you type?

  1. Tape the eaves. They are level, so the tape and the metal match.
  2. Tape each rake along the slope, or convert a level run somewhere else first. This page will not do that conversion.
  3. Add dormers and valleys yourself. The two boxes are one eave total and one rake total.
  4. Type the stick length from the bundle. Blank stays a linear-foot answer only.
  5. Type the lap in inches if the pieces must overlap. Blank means the full stick is used in the division.
  6. No price and no nail count. Corners that waste a miter are your extra stick, not a built-in percent.

What the Drip Edge Calculator Leaves Out

Public calculators seen on 20 November 2026 mixed a pitch factor, a 5 percent waste line, a starter-shingle bundle, and a nail spacing into the same tool. The pitch factor belongs with fascia when the rake was measured level. Starter bundles and nails were not given a fetched yield, so they are not on this page. A code sentence about a 2 inch lap was seen as a citation on a third-party page and was not opened, so it is not the default.

Roofing squares stay on the roofing squares calculator. This URL is the edge metal only. Demand is from the public result list. Ahrefs was not refreshed.

Frequently Asked Questions

How does the drip edge calculator get linear feet?

It adds the eave length to the rake length you type. Eighty plus 40 is 120 linear feet. It does not apply a pitch factor. Measure the rake along the slope before you type it.

Why is there no default stick length?

No manufacturer stick was fetched as a default. Public calculators often assume 10 feet. This page leaves sticks blank until you type the length on the bundle you will buy.

Does a blank overlap mean zero?

Yes. A blank overlap box does not subtract from the stick. Type the lap in inches when the pieces must overlap. A 10 foot stick and a 2 inch lap is a hand check in the copy, not the numbers in the boxes.

Is this a fascia board count?

No. Fascia boards, including a rise-per-12 stretch of a flat rake, are the fascia board calculator. This page is metal sticks from lengths you already measured. It does not price the metal.

Measure the Slope, Then Count the Sticks

The edge is a length. The bundle tells you the piece.

Get a Free Demo

All calculations are estimates based on historical information and should be verified by the user. This tool is provided as a free service for planning purposes only and is not a substitute for a professional assessment, a supplier quote, or applicable local code requirements.