Free Calculator · By SubcontractorHub Editorial Team · Published November 2026

Welded Wire Mesh Calculator for Sheets, Not Bar Lengths

A welded wire mesh calculator on this page multiplies slab length by slab width. Twenty-four feet by twenty feet is 480 square feet. Sheets stay blank until you type the panel.

Built by SubcontractorHub — the software contractors use to quote, finance, and run every job.

Book a Demo

How the Welded Wire Mesh Calculator Divides the Slab

Slab area, then a sheet you type, then an optional overlap.

Twenty-four by twenty is the slab in the boxes. It is not a driveway. Sheet size stays blank until you type the panel the yard sells.

This welded wire mesh calculator reads 480.0 square feet. No sheet count, because no sheet size was typed.

All calculations are estimates based on historical information and should be verified by the user.

Important: sheet size is typed

All calculations are estimates based on historical information and should be verified by the user. This tool is provided as a free service for planning purposes only and is not a substitute for a professional assessment, a supplier quote, or applicable local code requirements.

This Welded Wire Mesh Calculator Is Not a Rebar List

Rebar is counted in sticks and laps. Mesh on this page is counted in sheets that cover a rectangle. The rebar calculator stays the bar takeoff. Cubic yards of the same slab are the concrete calculator. A footing that is not this slab is the concrete footing calculator.

Overlap is taken off each side once. That double-counts the corner of the lap, which makes the usable sheet a little smaller than a perfect nest. It is a planning allowance. It is not a placement drawing, and it does not say where the sheet sits in the thickness of the slab.

Worked slab

Length 24 feet. Width 20 feet. The area is 480 square feet. Sheet boxes blank means no sheet count. Type both sheet sides together. An overlap with no sheet still does nothing, because there is no sheet to shorten.

LineInputExample
Length × widthfeet24 × 20
Areasquare feet480
Sheetlength and width, typedblank
Overlapinches, optionalblank
Sheetsarea divided by usable sheet, rounded upblank

How should you enter the sheet?

  1. Measure the slab rectangle in feet. Break an L-shape into rectangles and add the areas before you type one length and one width, or run the page twice.
  2. Read the sheet size off the bundle, in feet, and type both sides.
  3. Type an overlap in inches only if the drawings call for one. Blank means the full sheet.
  4. The page rounds the sheet count up. It does not add a second waste percent on top of that overlap.
  5. Do not use this count as a wire size. The page has no W-number.
  6. No price on this page.

What This Sheet Count Leaves Out

Pounds per square foot from a wire gauge showed up on a public calculator. The constant behind that weight was not fetched, so it is not here. If the yard sells by the pound, ask the yard. This page will not invent the steel weight.

A roll is the same division if you type the roll's length and width as the "sheet." The page does not know a roll from a panel. It only knows the rectangle you type.

A check you can do by hand: 480 square feet, a 5 by 10 sheet, and a 6 inch overlap, is 4.5 times 9.5, or 42.75 usable square feet, and 12 sheets after rounding up. Those sheet numbers are not in the boxes. Demand for this URL is from the public result list. Ahrefs was not refreshed. GSC, in the 16 November pull, already shows the rebar calculator gaining. This page sits next to that takeoff and does not replace it.

Frequently Asked Questions

How does the welded wire mesh calculator count sheets?

It divides the slab area by the sheet area you type, then rounds up. A 24 by 20 slab is 480 square feet. Sheets stay blank until you type a sheet length and a sheet width.

What does the overlap do?

If you type an overlap in inches, that length is taken off each side of the sheet before the sheet area is used. It is a planning allowance, not a nested layout. Leave it blank to use the full sheet.

Does this page weigh the mesh?

No. A public mesh calculator also offered pounds from a W-number. That table was not fetched. This page stops at a sheet count. It is not a rebar takeoff.

Is this a structural design?

No. It does not pick a wire size, a chair height, or a span. Those stay with the drawings. The count is how many sheets cover the rectangle after the overlap you type.

Type the Sheet, Then Cover the Slab

Bars are a different count. This page is sheets.

Get a Free Demo

All calculations are estimates based on historical information and should be verified by the user. This tool is provided as a free service for planning purposes only and is not a substitute for a professional assessment, a supplier quote, or applicable local code requirements.