Free Calculator · Published October 2026
Cubic Feet to Cubic Meters: Multiply by 0.02831685
One cubic foot is 0.02831685 cubic meters on the printed NIST line. Two cubic feet are 0.05663370 cubic meters.
Write cubic feet and cubic meters on the same tank note before anyone treats the number as gallons.
Built by SubcontractorHub — the software plumbing contractors use to quote, finance, and run every job.
Book a DemoHow Cubic Feet to Cubic Meters Uses 0.02831685
This converter follows one row on the NIST Guide to the SI, Appendix B.8. The cubic foot row multiplies by 2.831 685 and E-02 to reach cubic meters. Gallons counted from a cubic foot stay on cubic feet to gallons.
Cubic feet, or cubic meters of that volume.
All calculations are estimates based on historical information and should be verified by the user.
Important: All calculator results are ballpark estimates
All calculations are estimates based on historical information and should be verified by the user. This tool is provided as a free service for planning purposes only and is not a substitute for a professional assessment, a supplier quote, or applicable local code requirements.
What Are Cubic Feet to Cubic Meters Using?
This conversion multiplies by 0.02831685. The result is a volume label. It does not say how large a pressure tank is, how much media to order, or whether a sample passed a lab. Write cubic foot next to the factor so the next visit does not swap in a gallon count.
One factor, both directions
The NIST table prints 2.831 685 in the multiply-by column and E-02 in the exponent column. Read together, that is 0.02831685 cubic meters in one cubic foot. This page uses 0.02831685 so a cubic foot round-trips through cubic meters. It does not build the result from liters.
One cubic meter divided by 0.02831685 is the reverse cubic-foot count, shown at eight decimals on the worked table. The engine divided by 0.02831685. It did not divide by 7.48, and it did not use 0.001.
Common cubic foot volumes
Each row multiplies by 0.02831685 and shows eight decimal places. These are not recommended tank sizes.
| Cubic feet | Cubic meters |
|---|---|
| 1 | 0.02831685 |
| 2 | 0.05663370 |
| 5 | 0.14158425 |
| 10 | 0.28316850 |
| 100 | 2.83168500 |
Worked examples
One cubic foot is 0.02831685 cubic meters. Two cubic feet are 0.05663370 cubic meters. Ten cubic feet are 0.28316850 cubic meters. The reverse of one cubic meter divides by 0.02831685.
| Case | Cubic feet | Cubic meters |
|---|---|---|
| 1 cubic foot | 1.00000000 | 0.02831685 |
| 2 cubic feet | 2.00000000 | 0.05663370 |
| 10 cubic feet | 10.00000000 | 0.28316850 |
| 1 cubic meter | 35.31466247 | 1.00000000 |
A cubic foot is not a gallon and not a liter
Gallons from a cubic foot stay on cubic feet to gallons. A liter counted as cubic meters, using 0.001, stays on liters to cubic meters. Gallons counted as liters, using 3.7854, stay on gallons to liters. This page has no 7.48 and no 0.001.
What to write on the job ticket
Write five lines before the number leaves this page. A later visit should not have to guess which volume was used.
- The entered value, and whether it was cubic feet or cubic meters.
- The factor, 0.02831685, named as the NIST cubic foot line.
- Both results, at eight decimals.
- Which tank, tag, or sheet the volume came from.
- A note that 7.48 and 0.001 were not applied, and that the factor was not called exact.
What stays off this volume
A weight of water in a cubic foot is a different page. This converter does not use 62.416 pounds, 1,000 kilograms, or 993 kilograms. A chemical dose in milligrams per liter is a different question.
A water treatment dealer who saves the 0.02831685 note will not swap in 7.48 and call the result cubic meters. This conversion does not size a softener and does not say a sample passed a county rule. A private-well lab sheet is still the well water testing guide.
Frequently Asked Questions
How do cubic feet to cubic meters use 0.02831685?
Multiply cubic feet by 0.02831685. That is the NIST Appendix B.8 row for a cubic foot into a cubic meter, printed as 2.831 685 E-02. Divide cubic meters by the same factor to go back. The factor is not called exact, because boldface was not preserved.
Is 0.02831685 the same as 0.001 liters?
No. One liter is 0.001 cubic meters on a different NIST row, used by the liters to cubic meters converter. This page starts from a cubic foot. It does not pass through liters.
Does this page use 7.48 gallons?
No. Gallons in a cubic foot stay on the cubic feet to gallons converter. This tool uses 0.02831685 only.
What is 1 cubic foot in cubic meters?
One cubic foot is 0.02831685 cubic meters. Two cubic feet are 0.05663370 cubic meters. Ten cubic feet are 0.28316850 cubic meters. Those products use eight decimal places.
Is this a tank size?
No. The result is a unit change. It is not a contact-tank volume, a filter size, or a pass line on a lab sheet.
Save 0.02831685 Next to the Volume
The cubic feet, the cubic meters, and the NIST line belong on the customer record.
Get a Free DemoAll calculations are estimates based on historical information and should be verified by the user. This tool is provided as a free service for planning purposes only and is not a substitute for a professional assessment, a supplier quote, or applicable local code requirements. It does not size a tank.