Free Calculator · By SubcontractorHub Editorial Team · Published November 2026

House Wrap Calculator for the Wall, Not the Siding Price

A house wrap calculator on this page multiplies wall length by wall height. One hundred sixty feet by nine feet is 1440 square feet. Rolls stay blank until you type the roll.

Built by SubcontractorHub — the software contractors use to quote, finance, and run every job.

Book a Demo

How the House Wrap Calculator Nets the Wall

Length, height, optional openings, then a roll only if you type one.

One hundred sixty by nine is the wall in the boxes. It is not a house. Roll size stays blank until you type the square feet on the roll you will buy.

This house wrap calculator reads 1440.0 square feet net. No roll count, because no roll size was typed.

All calculations are estimates based on historical information and should be verified by the user.

Important: roll size is typed

All calculations are estimates based on historical information and should be verified by the user. This tool is provided as a free service for planning purposes only and is not a substitute for a professional assessment, a supplier quote, or applicable local code requirements.

This House Wrap Calculator Is Not a Siding Bid

Siding tools on this site price cladding. House wrap is the sheet behind that cladding, and this page counts area only. Sheathing sheets for the same wall are the plywood calculator. Studs in that wall are the stud calculator. Board-and-batten pieces are the board and batten calculator. None of those is a roll of wrap.

Gables are not a triangle button. If the wall is not a rectangle, add the extra area into the length and height you type, or add the square feet before you subtract openings. The page will not invent a gable.

Worked wall

Wall length 160 feet. Height 9 feet. Openings blank. The net area is 1440 square feet, the same as the gross. Type an opening total if you want it removed. Type the roll's square feet if you want a count. Overlap does nothing until the roll width is typed too.

LineInputExample
Length × heightfeet160 × 9
Grosssquare feet1440
Openingsoptional square feetblank
Netgross minus openings1440
Rollsonly if roll square feet are typedblank

How should you measure the wall?

  1. Add the exterior wall lengths that get wrap, and type that total as the length.
  2. Type the height of that band. A one-story wall and a two-story wall are not the same box.
  3. If you deduct windows and doors, add their areas first and type one openings number.
  4. If you do not deduct them, leave openings blank. The page will not decide.
  5. Type the square feet printed on the roll. Do not use a roll this page did not fetch.
  6. Type width and overlap together, or leave both blank. No price on this page.

What the House Wrap Calculator Leaves Out

A public calculator also offered seam tape and cap fasteners from a rule of thumb. Those rates were not fetched as a manufacturer instruction, so they are not on this page. Tape is a linear extra you can add after you know the course height.

Fascia length, which is the eave and the rake rather than the wall face, is the fascia board calculator. Soffit area under the eave is the soffit calculator. Leave those off the wall total.

A check you can do by hand: 1,440 square feet of wall, a roll you type as 900 square feet, and no overlap, is 2 rolls because 1,440 divided by 900 rounds up. The 900 is not in the box. It is an example of the division. Demand for this URL is from the public result list. Ahrefs was not refreshed.

Frequently Asked Questions

How does the house wrap calculator get square feet?

It multiplies the wall length you type by the wall height you type, then subtracts openings if you type them. One hundred sixty feet by nine feet is 1,440 square feet. Rolls stay blank until you type a roll's square feet.

Should openings come off the house wrap area?

Only if you type them. Some installers buy wrap for the full wall because the sheet is cut into the opening. This page subtracts the square feet you type and does not choose that practice for you.

Does the house wrap calculator price the siding?

No. Siding price tools are separate pages. This one stops at wall area and, if you type it, a roll count. No roll width was fetched as a default.

What does the overlap box do?

Nothing until you also type the roll width in feet. Then the roll's square feet are reduced by the share of the width the overlap uses. Leave both blank to use the full square feet you typed.

Measure the Wall, Then Read the Roll

The wrap is an area. The siding price is a different page.

Get a Free Demo

All calculations are estimates based on historical information and should be verified by the user. This tool is provided as a free service for planning purposes only and is not a substitute for a professional assessment, a supplier quote, or applicable local code requirements.