By SubcontractorHub Editorial Team·Published November 2026

Quick Answer
R-32 refrigerant, in EPA's 28 April 2023 SNAP rule, is HFC-32, also called difluoromethane. The rule prints GWP 675, ozone depletion potential zero, and ASHRAE safety group A2L. It is one component of R-454B, not the blend itself. This is not a charging procedure.
A quote that says only "A2L" has not named the gas. R-32 refrigerant is one name on that list. R-454B is another. The class page already says they are not the same word and stops before a GWP for this gas. This page prints the GWP the Federal Register actually printed, and it stops before a recovery step, a leak-sensor setpoint, or a cylinder price.
The 28 April 2023 Federal Register notice says HFC-32 is also known as R-32 or difluoromethane, CAS Registry Number 75-10-5. That is one substance. The same paragraph then defines blends that contain it. A pure gas and a blend that uses it are different products, even when the jug in the van has both labels in the same aisle.
Using the ASHRAE 34-2019 groups, the rule puts HFO-1234yf, HFC-32, and four blends from that section in the A2L safety group. A2L is the class. It is not a SKU. The class page lists more names than this rule's section. This article stays with the sentences in the rule that was fetched.
The environmental paragraph says HFO-1234yf, HFC-32, and those four blends have ozone depletion potentials of zero. It then says HFC-32 has a GWP of 675. The components it uses for the blend math are HFC-32, HFC-125, and HFO-1234yf, with GWPs of 675, 3,500, and less than four. Weighted by mass, the rule prints about 700, 240, 470, and 150 for R-452B, R-454A, R-454B, and R-454C.
In the residential and light commercial comparison, the rule says HFC-32's GWP of 675 is higher than some acceptable substitutes, including R-454B at about 470, and lower than others, including R-410A at 2,090. That is a comparison of numbers in the rule. It is not a sentence that says an installed R-410A system must be ripped out, and it is not a match between a coil and a jug.
| Line | What the 28 April 2023 rule prints | Where |
|---|---|---|
| Name on the rule | HFC-32, also R-32, also difluoromethane | CAS 75-10-5 |
| Safety group | A2L, with HFO-1234yf and four blends in that section | ASHRAE 34-2019, as the rule cites it |
| GWP | 675 | Same paragraph as the blend math |
| Ozone depletion | Zero, with the blends in that section | Environmental information |
| R-454B | 68.9 percent HFC-32 and 31.1 percent HFO-1234yf | GWP about 470, not 675 |
| R-410A in that comparison | GWP of 2,090 | Not a ban sentence |
The rule describes R-454B as 68.9 percent by weight HFC-32 and 31.1 percent HFO-1234yf. Its mass-weighted GWP in that paragraph is about 470, not 675. Writing "R-32" on a system built for the blend, or the reverse, is not supported by anything fetched here. The blend's own page is R-454B refrigerant. The class list, and the sector dates this article will not copy, are on A2L refrigerant.
Other blends in the same paragraph also contain HFC-32: R-452B at 67 percent, R-454A at 35 percent, and R-454C at 21.5 percent. A drum of the pure gas is not a shortcut to any of those recipes. The rule is describing composition. It is not a field mixing instruction.
The job record should carry the name the equipment was built for. If that name is R-32, the record says R-32, plus the fact that the fetched rule calls it a pure HFC with GWP 675 and safety group A2L. If the name is a blend, the record says the blend. "New refrigerant" and "A2L" are not substitutes for the name.
Where the cylinder sits in the van is a layout question, not a GWP question. That layout is the HVAC van setup guide. What else is on the truck, as a list rather than a floor plan, is the HVAC tools list. Certification names, which this page does not retake, stay on HVAC certification.
A public search on 18 November 2026 for this head term surfaced the Federal Register rule above, a New York Clean Heat fact sheet, a sensor maker's R-32 note, and a reclaimer brochure. Only the Federal Register text was used for the numbers. The fact sheet's table was not quoted. No Ahrefs volume was on the 8 November 2026 pull for this exact head term, so none is invented. Demand for the page is that public result list plus the gap on the class article, which still refuses a GWP for this gas.
R-32 refrigerant is the single-component HFC that EPA's 28 April 2023 SNAP rule also calls HFC-32 and difluoromethane, CAS 75-10-5. The same rule places it in the ASHRAE A2L safety group and prints a GWP of 675 and an ozone depletion potential of zero. It is not a blend.
No. The 28 April 2023 rule says R-454B is a blend of 68.9 percent HFC-32 and 31.1 percent HFO-1234yf, with a GWP of about 470. R-32 refrigerant is the pure component. The rule does not say you can top one off with the other.
No. The rule compares GWPs. It prints about 2,090 for R-410A and 675 for HFC-32 in the residential and light commercial comparison. Sector dates for what may be manufactured or installed stay on the A2L refrigerant page. This article does not restate them.
The refrigerant name the equipment was built for, not the letters A2L alone. If the nameplate says R-32, write R-32. If it says R-454B, write R-454B. This page does not give a recovery procedure, a charge limit, or a cylinder price.
SubcontractorHub
AI proposals, sales pipeline, and project management — all in one platform.
30 minutes. No commitment.